The Cisco 300-115 SWITCH exam validates the switching skills and knowledge of test-takers as they relate to planning, verifying, and configuring the implementation of multifaceted enterprise switching solutions that use the Cisco Enterprise Campus Architecture.

Cisco 300-115, Implementing Cisco IP Switched Networks, is a qualifying exam for the CCNP Routing and Switching and the CCDP credentials. The test is made up of 30 to 40 questions and the time allotted for its completion is 120 minutes. It is available only in English and Japanese, and the candidates can register for it via Pearson VUE. The certification exam validates that you have what it takes to plan, configure, and verify the implementation of multifaceted enterprise switching solutions that utilize the Cisco Enterprise Campus Architecture. Suffice to mention that this test covers the highly secure integration of WLANs and VLANs.

Overview of Cisco 300-115 Exam Topics

In this section, we’ll take a broad look at specific exam topics as highlighted by Cisco. It is important to mention that these objectives are standard guidelines for the exam content. There can be some other areas that are related to them that may also be included in your version of the test. In addition to this, the guidelines may also change any time without any prior notice given to the candidates. This means that prior to commencing your exam preparation, you should take time to go through the exam content on the certification page. This will prevent you from studying dated study materials.

Cisco Certifications

CCNA & CCNP Routing & Switching

Specialization Exams

Essentially, the Cisco 300-115 SWITCH exam covers three broad topics: Layer 2 Technologies, Infrastructure Security, and Infrastructure Services. Let’s look at them in detail.

Layers 2 Technologies – 65%

This exam topic covers about 65% of the total questions. It means that this should be your main focus during your preparation. Under this subject, there are other subtopics that one must study in order to be fully prepared for the certification exam. The candidates must learn how to configure and verify the switch administration. Here, they must learn all about SDM templates, managing MAC address table, and troubleshooting Err-disable recovery. They also should understand how to configure and verify Layer 2 protocols, including CDP, LLDP, and UDLD. The test takers should also be able to configure and verify VLANs before attempting the test. This covers access ports, VLAN database, Normal, voice VLAN, and extended VLAN. Another area under this objectivewhere the studentsshould develop competence is configuration and verification of trunking. This includes dot 1Q, VTPv1, VTPv2, VTMv3, and VTP pruning, as well as Manual pruning, and Native VLAN. It is also critical to understand the process involved in configuring and verifying Ether Channels. This entails LACP, PAgP, and manual, Layer 2 and Layer 3,EtherChannel misconfiguration guard, and Load balancing. Another area you need to focuson is configuration and verification of spanning tree. The examinees must understand the fundamentals of Switch priority, path cost, port priority, and STP timers; PVST+, MST, and RPVST; Loop guard & Root guard; Port Fast, BPDU guard, and BPD filter. One should also understand how to configure and verify some other LAN switching technologies, like the RSPAN and SPAN. Additionally, they should be able to explain chassis virtualization & aggregation technologies, such as Stackwise.

Infrastructure Security – 20%

Although the percentage associated with this topic is not as much as the one above, the individuals still need to pay close attention to it and study it extensively. It can be the difference between a successful score and a poor result. Under this topic, the candidates are required to learn how to configure and verify some switch security features. These include IP Source Guard; DHCP snooping; Dynamic ARP inspection; Storm control; port security; and Private VLAN. Additionally, the applicants should be able to explain device security with the use of Cisco IOS AAA with RADIUM and TACACS+. This covers areas such as Local privilege authorization fallback and AAA with RADIUS and TACACS+.

Infrastructure Services – 15%

This part requires that the test takers understand the process involved in configuration and verification of first-hop redundancy protocols. This covers HSRP, GLBP, and VRRP. Just like the previous subject, this topic also has a low percentage but its understanding can make a little difference in your success in the certification exam.

It is essential to mention that the percentage on each of the topics indicates the amount of questions that may be expected from each of them. It is important to pay close attention to these numbers to enable you to know what to focus on during your study.

Overview of Cisco 300-115 Preparation Options

There are quite a good number of resources that are available for the Cisco 300-115 exam preparation. Cisco has a list of training resources on its website and you may want to take some time to check them out. Let’s take a look at them here.

Classroom training

Cisco has the authorized learning partners who take the candidates at instructor-led classes across the world. You can check the certification page to see the recommended training available for the 300-115 SWITCH exam.


The certification vendor also offers self-paced online courses and prep materials for the Cisco 300-115 exam. There are a couple of recommended training for the students, including Implementing Cisco IP Switched Networks (SWITCH v2.0), Cisco Certification Practice exam, and Cisco learning labs for CCNP SWITCH. You can access the links to these e-learning resources on the certification page.

Mock tests

Finally, you have to dedicate enough time to practice tests. This will help you gain mastery in your test-taking and time management skills. PrepAway has enough prep tools in this regard to get you started on a very good note.

Other useful resources

In addition to the above, there are also book resources that you can explore to get the best of your exam preparation. Moreover, you can join a couple of study groups to help you learn from other test-takers. And it is necessary that you try your hands-on lab environments in order to be adequately equipped for the actual exam. Check the certification page to get the links to the hands-on lab environments and the study group.


There are a lot of study materials that can help you during your exam preparation and you should use all of them. Whether the topic is difficult or not, the proper training and qualified help from the IT professionals can get water from a flint. Get good use of preparation resources and obtain high results.